Eurotherm 2116i Provozní pokyny stáhnout pdf

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -1- HA026248

2132i and 2116i

Temperature and Process Indicator and Alarm Units

Installing and Operating Instructions

IMENSIONS AND

NSTALLATION

Model 2132i

Model 2116i

LECTRICAL

ONNECTIONS

To install the indicator

Please read the safety information on pages 5 & 6 before

proceeding.

1. Prepare the panel cut-out to the size shown.

2. Insert the indicator through the cut-out.

3. Spring the panel retaining clips into place. Secure the indicator

in position by holding it level and pushing both retaining clips

forward.

4. Peel off the protective cover from the display

Unplugging the indicator

The indicator can be unplugged from its sleeve by easing the

latching ears outwards and pulling it forward out of the sleeve.

When plugging the indicator back into its sleeve, ensure that the

latching ears click into place to maintain the IP65 sealing.

10mm

(0.4in)

38mm

(1.5in)

(Not to

scale

)

Recommended minimum

spacing of indicators in

both sizes

Output ratings

Relay: 2A, 264Vac resistive

Logic: 9Vdc, 12mA (non-isolated from sensor input).

Over current protection

Use a maximum 2A fuse for the indicator supply and relay output.

A suitable fuse is EN60127 (type T).

Wire Sizes

The screw terminals accept wire sizes from 0.5 to 1.5 mm

(16 to 22

AWG). Hinged covers prevent hands or metal making accidental

contact with live wires. The rear terminals screws should be

tightened to 0.4Nm (3.5lb in).

22.2

-0.0 +0.3

x 45

-0.0 +0.6

2132

OP1

OP2

Panel cut-out

24mm

(0.95in)

0.88

-0.0 +0.1

x1.77

-0.0 +0.02

103mm (4.01in)

48mm (1.89in)

Panel retaining clipsLatching ears

Inch

Sensor

input

External

Relay module

Relay*

Output

Logic*

I/O

T/C

Alarm

ack/reset

Pt100

Model 2116

Neutral

Line

V-

V+

20-29Vac/dc

Low voltage supply

85-264Vac

2.49

Ω

External Relay

module

Neutral

Relay*

Output

Logic*

I/O

Line

Sensor input

T/C

Alarm

ack/reset

Pt100

Model 2132

AA LNABV- V+

1B 1A

85-264Vac

20-29Vac/dc

Low voltage supply

24 24

2.49

Ω

RUN

HOLD

2216

MAN

OP1

OP2

SP2

REM

48mm (1.89in)

Panel cut-out

45 x 45mm

-0.0 +0.6

1.77 x 1.77in

-0.00 +0.02

103mm (4.01in)

48mm

(1.89in)

Panel retaining clips

Latching ears

*Not fitted in indicator only units. Also terminals 1A and

1B not fitted in indicator only unit.

This indicator meets the European directives on safety and

EMC

Thank you for choosing the 2132i or 2116i indicator and alarm unit. It

will provide accurate measurement and display of temperature and

other process variables with up to two alarm outputs for operator alert

and process protection.

Models 2132i/AL and 2116i/AL are

Indicating alarm units

which

come with an alarm relay output and logic I/O fitted.

Models 2132i/ND and 2116i/ND are

Indicator only units

which

come without the alarm relay output or logic I/O fitted. Alarms can

still be configured and flashed as messages in the main display but

they will not be able to operate a physical output.

The indicator is supplied configured according to the ordering code

given on page 5. Check the coding on the side labels to determine

the configuration of your particular indicator.

ENG

1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - 2132i and 2116i

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -1- HA0262482132i and 2116iTemperature and Process Indicator and Alarm UnitsInstalling a

Strany 2

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -2- HA026248OPERATIONSwitch on the indicator. Following a 3 second self-test sequence,y

Strany 3

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -3- HA026248PARAMETER LISTSUse these lists to change: • The alarm setpoints •The alarm

Strany 4 - Logic only

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -4- HA026248CONFIGURING THE INDICATORSelect configuration level to change: •The display

Strany 5

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -5- HA026248ORDERING CODEThe indicator is supplied configured according to the ordering

Strany 6 - SERVICE AND REPAIR

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -6- HA026248SERVICE AND REPAIRThis indicator has no user serviceable parts. Contact you

Další dokumenty pro Měření, testování a kontrola Eurotherm 2116i

Zobrazit dokument Eurotherm 2116i Uživatelský manuál

Eurotherm 2116i Uživatelský manuál (24 stránky)

Eurotherm 2116i Uživatelský manuál (2 stránky)

Komentáře k této Příručce

Žádné komentáře

Eurotherm 2116i Provozní pokyny

Procházejte online nebo si stáhněte Provozní pokyny pro Měření, testování a kontrola Eurotherm 2116i. Eurotherm 2116i Operating instructions Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Měření, testování a kontrola Eurotherm 2116i

Komentáře k této Příručce

Související produkty a manuály pro Měření, testování a kontrola Eurotherm 2116i