Eurotherm 2116i Provozní pokyny stáhnout pdf (Strana 5)

Issue 3, Nov-98. Applies to software versions 1.3 & 1.4 -5- HA026248

RDERING

ODE

The indicator is supplied configured according to the ordering code shown below.

Model

number

Function Supply

voltage

Manual Logic

I/O

Alarm

Relay

Output

Sensor

input

Setpoint

min

Setpoint

max

Units External

relay

module

Input

adaptor

2132i

2116i

ECHNICAL

PECIFICATION

Display 4 digit, green. 10mm high characters

Supply voltage High voltage unit: 100Vac -15% to 240Vac +10%, 48-62Hz. Power consumption: 5Watts maximum

Low voltage unit: 24Vdc or ac -15%, +20% DC to 62Hz, Power consumption: 5Watts maximum

Operating ambients 0 to 55

C. 5 to 95%RH, non condensing

Storage temperature -30

C to +75

Output ratings Relay(isolated): Maximum: 264Vac, 2A resistive. Minimum: 12Vdc, 100mA

Logic I/O: 9Vdc at 18mA (non-isolated from sensor input). Can be used as alarm output or alarm acknowledge

input

Calibration accuracy

± 1

C or ±0.25% of reading whichever is greater

Cold junction compensation >30 to 1 rejection of ambient temperature change. Uses INSTANT ACCURACY

cold junction sensing

technology to eliminate warm-up drift and respond rapidly to ambient temperature changes.

Input filtering Off to 999.9 seconds

EMC standards Generic emissions standard EN50081-2 and immunity standard EN50082-2 for industrial environments

Safety standard EN 61010. Installation category II. (Voltage transients on the power supply must not exceed 2.5kV). Pollution

degree 2. All isolated inputs and outputs have reinforced insulation to protect against electric shock.

Atmosphere Not suitable for use above 2000m or in explosive or corrosive atmospheres

Panel sealing IP65 (EN 60529), or NEMA 4X

AFETY AND

EMC I

NFORMATION

Safety

This indicator complies with the European Low Voltage Directive

73/23/EEC, amended by 93/68/EEC, by the application of the

safety standard EN 61010.

Electromagnetic compatibility

This indicator conforms with the essential protection requirements

of the EMC Directive 89/336/EEC, amended by 93/68/EEC, by the

application of a Technical Construction File. This indicator

satisfies the general requirements of the industrial environment

defined in EN 50081-2 and EN 50082-2.

GENERAL

The information contained in these instructions is subject to change

without notice. While every effort has been made to ensure the

accuracy of the information, Eurotherm Controls shall not be held

liable for errors contained herein.

Unpacking and storage

The packaging should contain the indicator, two panel retaining

clips, a 2.49Ω current sense resistor and this instruction leaflet.

If the packaging or the indicator are damaged, do not install the

product but contact your nearest Eurotherm Controls agent.

Continued on the next page

External relay module

XX Not fitted

R7 Fitted (Operated

by the logic

output)

Supply voltage

VH 85-264Vac

VL 20 -29V dc or ac

Alarm Relay Output

XX Disabled*

Non-latched alarms

FH High alarm 2

FL Low alarm 2

AL High alarm 2 &

low alarm 3

Latched alarms

HA High alarm 2

LA Low alarm 2

AA High alarm 2 &

low alarm 3

NW New alarm

Manual

XXX None

ENG English

FRA French

GER German

NED Dutch

SPA Spanish

SWE Swedish

ITA Italian

Sensor input Display range and

Setpoint min & max limits

Thermocouples

J Type J -210 to 1200 -340 to 2192

K Type K -200 to 1372 -325 to 2500

T Type T -200 to 400 -325 to 750

L Type L -200 to 900 -325 to 1650

N Type N -200 to 1300 -325 to 2370

R Type R -50 to 1768 -58 to 3200

S Type S -50 to 1768 -58 to 3200

B Type B 0 to 1820 32 to 3308

P Platinell II 0 to 1369 32 to 2496

Resistance thermometer

Z Pt100 -200 to 850 -325 to 1562

Custom downloaded inputs

C Type C -W5%Re/W26%Re

(default custom sensor)

0 to 2319 32 to 4200

D Type D - W3%Re/W25%Re 0 to 2399 32 to 4350

E E thermocouple -200 to 999 -325 to 1830

1 Ni/Ni18%Mo 0 to 1399 32 to 2550

2 Pt20%Rh/Pt40%Rh 0 to 1870 32 to 3398

3 W/W26%Re (Engelhard) 0 to 2000 32 to 3632

4 W/W26%Re (Hoskins) 0 to 2010 32 to 3650

5 W5%Re/W26%Re (Engelhard) 10 to 2300 50 to 4172

6 W5%Re/W26%Re(Bucose) 0 to 2000 32 to 3632

7 Pt10%Rh/Pt40%/Rh 200 to 1800 392 to 3272

8 Exergen K80 I.R. Pyrometer -45 to 650 -49 to 1202

Process inputs (linear)

M -9.99 to +80mV Scalable -999 to 9999

Y 0 to 20mA Scalable -999 to 9999

A 4 to 20mA Scalable -999 to 9999

V 0 to 10Vdc (

input adapter required)

Scalable -999 to 9999

Units

K Kelvin

X Linear input

Logic I/O

XX Disabled*

Logic input

AC Alarm ack/reset

KL Keylock

Non-latched alarms

FH High alarm 1

FL Low alarm 1

Latched alarms

HA High alarm 1

LA Low alarm 1

NW New alarm

Function

ND Indicator only*

AL Indicating alarm

unit

Input Adaptor

XX None

V1 0-10Vdc

A1 0-20mA sense

resistor (2.49

Ω

0.1%)

*If ‘ND’ (Indicator only) is

specified in the function field,

then XX must be entered in

the Logic I/O and alarm 2

relay fields.

1 2 3 4 5 6

Komentáře k této Příručce

Žádné komentáře

Eurotherm 2116i Provozní pokyny Strana 5

Komentáře k této Příručce

Související produkty a manuály pro Měření, testování a kontrola Eurotherm 2116i